Steering and power supply

ERO-32WS-0

These type of motor speed controllers are equipped with Wi-Fi module.

Description

ERO-32WS-0 can operate in two modes:

Fixed mode: in which motor speed of the controlled device remains constant.
Zonal mode: in which motor speed of the controlled device depends on time schedule defined by the user.

Controllers may be operated with the usage of a special application (BleBox) available for mobile phones and tablets (Android, iOS and Windows Phone).

Controller is compatible with:

Hybrid Turbowent Tulipan
Hybrid Turbownets
Hybrid Turbowents Plus
Draught generators GCKV
Hot air ventilators ANeco1, 2, 3 – II generation

Continue reading “ERO-32WS-0”

Steering and power supply

ARO

ARO can operate in preset modes.

Description

Automatic motor speed controllers enable operation in following modes:

Manual mode: in which motor speed of the controlled device is constant – user may set one of ten different speed values.
Automatic mode: in which motor speed of the controlled device depends on temperature detected by the analogue KTY84 thermal probe (an external element, included in the set, which may be placed f.e. in the fireplace hood).

Controller is compatible with AN1, 2, 3

Technical information

Type	ARO
Mounting	Under surface
Voltage [V/Hz]	230 / 50
Maximal load [W]	300

Steering and power supply

ERO-31MW-0

ERO-31MW-0 motor speed controller is designed for working with hybrid chimney cowls produced by DARCO. ERO 31MW-0 is to be mounted unside the hybrid cowl steering box.

Using this type of controller gives much protection against unauthorized interference and changing the Turbowent’s working parameters. Additionally it allows to reduce the amount of cables needed. For proper cowl’s working only one cable with two wires (power supply) is needed.

Controller is compatible with:

Technical data

Type	ERO-31-MW-0
Voltage [V DC]	20-24
Nominal power [W]	0,3
Max current [mA]	40
Fuse [A]	2,5 (type 0034.6018)
Ambient temperature [°C]	-20 – +60
Humidity [%]	0 – 80
Measurements [mm]	74 x 56 x 22
Weight [g]	33

image gallery

Download

Catalogue card

YT

Steering and power supply

ERO32MS-0

ERO-32MS-0 controllers are designed for motor speed steering of devices equipped with brushless (BLDC type) motors produced by DARCO and as regulated 0-5 V DC / 0-10 V DC general purpose voltage sources.

Description

Controller is designed for mounting on standard TS-35 rail (electric cabinets) is available. Controller is equipped with a diode signaling operating status of powered devices. Parameters of the cowls and hot air ventilators can be changed by manual setting of the knob. Controller is compatible with devices produced by DARCO:

Hybrid Turbowent Tulipan
Hybrid Tubrowents
Draught Generators GCKV
Hot Air Ventilators ANeco1, 2, 3 – II generation

Technical information

Type	ERO-32-MS-0
Voltage [V DC]	20-24
Nominal power [W]	0,3
Max current [mA]	30
Max R output load [mA]	5
IP protection class	IP40
Ambient temperature [°C]	-20 – +60
Humidity [%]	0 – 80
Measurements [mm]	18 x 90 x 63
Weight [g]	48

image gallery

Download

Catalogue card

YT

Steering and power supply

RO-DSS2

RO-DSS2 manual motor speed controller is a digital controller, using IGBT transistors eliminating the so-called motor “buzzing” effect – that can appear with the standard, thyristor-based regulators.

Description

Motor speed of the controlled device can be changed using keyboard on the front panel. Front part is also equipped with an array of LED diodes, informing about current setting.

Controller is compatible with:

Technical data

Type	RO-DSS2
Mounitng	On surface
Voltage [V / Hz]	230 / 50
Maximal load [W]	350

Image gallery

Download

Catalogue card

YT

Steering and power supply

RO-N and P

RO controller is used for precise regulation of the speed of a single-phase motor.

Description

RO-N / RO-P digital manual speed controllers are used for precise adjustment of rotating speed of single-phase motors (having 10 possible speed settings).

Controller is compatible with:

Technical data

Type	RO-P	RO-N
Voltage [V/Hz]	230/50
Max load [W]	400
Adjustment range [%]	20 – 100
Adjustment steps	12
Measurements [mm]	81 x 81 x 70	81 x 81 x 45
Weight [g]	120	120
Version	Under surface	On surface

image gallery

download

Catalogue card

YT

Steering and power supply

RO-200

RO-200 analogue manual motor speed controller is used for precise adjustment of rotating speed of single-phase motors.

description

RO-200 motor speed controller is used for adjustment of rotating speed of single – phase motors. Device can be used in installations where motor speed is governed by adjusting effective voltage given to the winding. Unit is dedicated to work with AN hot air ventilators and GCK draught generators produced by Darco . Controller is compatible with:

Controller is compatible with:

Technical information

Type	RO – 200
Voltage [V/Hz]	230/50
Maximal load [W]	200
Adjustment rate [%]	20 – 100
Working type	constant
Ambient temperature [ºC]	0 – 40
Protection class	IP40
Weight [g]	130
Measurements [mm]	81 x 81 x 71

Image gallery

Download

Catalogue card

YT

Darco system

Calculator for wiring

The Calculator Wiring application is used to calculate the maximum cable lengths and to determine the types of power cabinets intended for Hybrid Turbows produced by DARCO Sp. z o.o.

Application

Application

Download Calculator for wiring

Darco system

Air intake sets

Air intake sets provide fresh air into the building. They can be mounted in the walls above or next to the windows in living spaces or in boiler rooms.

Kup ten produkt

Description

ROUND AIR INTAKE SETS:

Air intake set provides fresh air into the building. It is to be mounted above or next to the window, in the wall. Basic version is equipped with an air intake that assures proper air supply from outside. It is constructed in a way that protects from rainwater and is also equipped with wire mesh against rodents. On the side mounted inside the building air intake set is equipped with a flap valve with insulation, that prevents from water vapor condensation in winter as well as reduces noise. Valve allows to regulate the airflow precisely.

Air intake set can be additionally equipped with airflow stabilizer. It controls the airflow: limits the air supply to certain limits as well as protects from backflow.

Air intake set with heater provides fresh and preheated air into the building. Thermostat turns the heating module on when temperature falls below 3°C and switches it off when temperature rises above 10-15°C. Semiconductor heating elements automatically regulate power consumption in relation to the amount and temperature of flowing air. Basic version is equipped with a flap valve. Optionally a version with stabilizer is available.

Each air intake set includes a filter (separately in the box, to be mounted by the user). Filter enables effective capturing of dust and other particles carried by the air.

RECTANGULAR AIR INTAKE SETS:

Air intake set provides fresh air into the building. It is to be mounted in the outside wall. It is equipped with an air intake, main channel and a flap valve. Air intake is an outer element that assures protection: from rainwater, it is also equipped with wire mesh against rodents. On the side mounted inside the building air intake set is equipped with a flap valve with insulation, that disperses incoming air as well as allows to regulate the airflow precisely. Insulation prevents from water vapor condensation in winter as well as reduces noise. Air intake set is connected with flap valve with a channel of adjustable length, that allows to adjust device to wall of 280÷550 mm thicknesses. Air intake set can be additionally equipped with a special directional valve that protects from backflow.

FOR VENTILATION

Technical data

ROUND AIR INTAKE SETS:

Version	Additional equipment	Diameters
Round air intake set/ Window recess air intake set	Flap valveFilter	Ø80
		Ø110
		Ø150
	Flap valve airflow stabilizer Filter	Ø80
		Ø110
		Ø150
Round air intake set with heater/ Window recess air intake set with heater	Flap valve HeaterFilter	Ø80
		Ø110
		Ø150
	Flap valve Heaterairflow stabilizerFilter	Ø80
		Ø110
		Ø150

RECTANGULAR AIR INTAKE SETS:

Type:	NP1, NPS1, NP2, NPS2
Measurements:	See catalogue card*
Material:	See catalogue card*
Warranty:	2 years

* Catalogue card is availabe in “Download” tab.

IMAGE gallery

Download

Catalogue card

National Declaration of Performance – Round Air Intake Sets

National Declaration of Performance – Rectangular Intake Sets

National Declaration od Performance – Round Air Intake Sets with window recess inlet

Declarations of Conformity – Air Intake Sets with heater type

YT

How to work Air intake set?

Darco system

Air intake sets

Air intake sets provide fresh air into the building. They can be mounted in the walls above or next to the windows in living spaces or in boiler rooms.

Kup ten produkt

Description

ROUND AIR INTAKE SETS:

Air intake set provides fresh air into the building. It is to be mounted above or next to the window, in the wall. Basic version is equipped with an air intake that assures proper air supply from outside. It is constructed in a way that protects from rainwater and is also equipped with wire mesh against rodents. On the side mounted inside the building air intake set is equipped with a flap valve with insulation, that prevents from water vapor condensation in winter as well as reduces noise. Valve allows to regulate the airflow precisely.

Air intake set can be additionally equipped with airflow stabilizer. It controls the airflow: limits the air supply to certain limits as well as protects from backflow.

Air intake set with heater provides fresh and preheated air into the building. Thermostat turns the heating module on when temperature falls below 3°C and switches it off when temperature rises above 10-15°C. Semiconductor heating elements automatically regulate power consumption in relation to the amount and temperature of flowing air. Basic version is equipped with a flap valve. Optionally a version with stabilizer is available.

Each air intake set includes a filter (separately in the box, to be mounted by the user). Filter enables effective capturing of dust and other particles carried by the air.

RECTANGULAR AIR INTAKE SETS:

Air intake set provides fresh air into the building. It is to be mounted in the outside wall. It is equipped with an air intake, main channel and a

flap valve. Air intake is an outer element that assures protection: from rainwater, it is also equipped with wire mesh against rodents. On the side mounted inside the building air intake set is equipped with a flap valve with insulation, that disperses incoming air as well as allows to regulate the airflow precisely. Insulation prevents from water vapor condensation in winter as well as reduces noise. Air intake set is connected with flap valve with a channel of adjustable

length, that allows to adjust device to wall of 280÷550 mm thicknesses. Air intake set can be additionally equipped with a special directional valve that protects from backflow.

for ventilation

Technical data

ROUND AIR INTAKE SETS:

Version	Additional equipment	Diameters
Round air intake set/ Window recess air intake set	Flap valveFilter	Ø80
		Ø110
		Ø150
	Flap valve airflow stabilizer Filter	Ø80
		Ø110
		Ø150
Round air intake set with heater/ Window recess air intake set with heater	Flap valve HeaterFilter	Ø80
		Ø110
		Ø150
	Flap valve Heaterairflow stabilizerFilter	Ø80
		Ø110
		Ø150